description: 2.5 m cable (15-pin to 26-pin D-Sub and leads) to connect the NI 9512 to the P7000 stepper drive. 1 m cable (MDR to 37-pin D-Sub) to connect the NI 9512 to a 37-pin connector block. 37-pin connector block for spring-type connectivity to motion I/O and encoder feedback....
$0.00
Ex Tax:$0.00
description: 1 m Y-cable (15-pin D-SUB and MDR to 37-pin D-SUB) to connect the NI 9512 to 37-pin connector blocks. 37-pin connector blocks for spring-type connectivity to third-party drives and motion I/O....
$0.00
Ex Tax:$0.00
description: 2.5 m cable to directly connect NI 951x C Series drive interface modules to AKD servo motor drive. Cable and all connector blocks included. 15-pin D-Sub and MDR to AKD drive connectors....
$0.00
Ex Tax:$0.00
description: Higher-Power Motor Screw-Terminal Accessory for NI 9505 Increased output power for the NI 9505 module. Integrated strain relief for accessory. Additional strain relief for external cabling. With the NI 9931 attached, the NI 9505 can deliver a maximum current of 7.3 A at 40 ºC, 1 A at 70..
$0.00
Ex Tax:$0.00
description: Adapters for Yaskawa, Panasonic, Mitsubishi Drives NI MCA-7790 adapters connect the NI PCI-7390 to popular drives in position (pulse) command mode. Specific versions for Yaskawa Sigma II, Mitsubishi MR-J2S, and Panasonic Minas A drives. Included status LEDs and screw terminals for addit..
$0.00
Ex Tax:$0.00
description: 6.3 A, 24 VDC Universal input voltage (85 VAC to 265 VAC). Regulated output voltage. Short circuit/overload/overvoltage protection. Configure Complete CompactRIO System....
$0.00
Ex Tax:$0.00
description: 6.7 A, 48 VDC Universal input voltage (85 VAC to 265 VAC). Regulated output voltage. Short circuit/overload/overvoltage protection. Configure Complete CompactRIO System....
$0.00
Ex Tax:$0.00
description: Connector connects NI motion controllers to the UMI-7764. 68-pin VHDCI offset male connector connects to NI motion controllers. 68-pin .050 Series D-type female connector connects to UMI-7764 motion interfaces....
$0.00
Ex Tax:$0.00
description: Connects NI motion controllers to NI MID-76xx, MCA-7724, or UMI-7774/2 devices or SSR cable adapters. 68-pin VHDCI offset male connector that connects to NI motion controllers. 68-pin VHDCI offset male connector on other end that connects to universal motion interfaces....
$0.00
Ex Tax:$0.00
description: Shielded Cable Assembly (Unterminated), 2 m 2 m length. Unterminated for custom wiring. Ideal for custom machines and OEM applications. For use with NI R Series devices and NI 735x, 734x, and 733x motion controllers. Also compatible with NI M Series DAQ and NI 6143 S Series DAQ devices...
$0.00
Ex Tax:$0.00
description: Connects an AKD servo motor drive through a UMI to a NI Motion Controller. Must be used between a Universial Motion Interface (UMI) and an AKD servo drive. 2.5 meter cable length....
$0.00
Ex Tax:$0.00
description: Built-in inhibit logic. Host bus +5 VDC monitor with built-in driver inhibit control. Per-axis motion signal breakout. 1 or 20 MHz quadrature encoder rates. Connects NI 735x/734x/733x motion controllers to third-party power drives....
$0.00
Ex Tax:$0.00